超声波焊接机器是爱我司较近来来研发团队的新几代全被动夹胶91吃瓜网 打磨裝备。有着操作容易，求同存异性强，打磨要求物美价廉特点。
This machine was research and development in our company. IT`s easy to use ,highly adaptab.
一：系统设计(Structure of machine)
工具框架图得到标准方管、扁铁、方管电焊而成。一般器官固溶处理妥善处理后超大型龙门铣工作。一致身体机能高，抗压强度大。得到两端式构造组合公式而成。一号段为野生植物有助于放料及发送局部性，搭配主动地精确品牌定位管理装修标准及靠栅精确品牌定位管理装修标准。第二个段包罗高低不平对刀打孔管理装修标准、切膜管理装修标准、热处理加热管理装修标准、有助于开料管理装修标准。
Frame was made with international square steel tube and box iron by welding.The key position had been annealing treatment and gantry milling. So the frame has high stability and strength.
Two-part construction to assemble the machine. The first part is the artificial auxiliary feeding and transmission part, equipped with automated positioning system. The second paragraph contains the upper and lower knife cutting system, the cutting film system, the heating system, and the auxiliary discharge system.
二：机气参数设置(Machine Parameters)
1. 机器设备部件外形尺寸：6735*5640*1412mm（估计）
刷卡机再生厚度：11700*2260*1500mm（40尺标柜）
参量：4500KG（总重量）
2.粗加工产值：最多3700*2500mm；面值最小400*400mm
3. 切割器刻薄产值：3+X+3mm---8+X+8mm
4. 割孔强度：1—2刀/30分钟
5.热处理加热水温和时期：收入设置好
6. 龙门刀头挪动数率：0---80米/分钟的时间。
7.刀头下压压差及掰片压差：液压配比阀合理
1.Size of machine:6735*5640*1412mm
2.Weight:about 4500KG
3.Processing range of glass size:400*400mm --- 3700*2500mm
4.Processing range of glass thickness:3+X+3mm---8+X+8mm
5.Cutting speed: cutting twice in one minute
6.Temperature and time of heating: Adjust by operater
7.Pressure of pushing and breaking: Adjust by operater
三 ：广州POS机软件设置技能摆才(Machine configuration)（可所选设立武器装备摆货）
1. 伺服控制器电气：中国台湾台达
2. 安装伺服控制器：香港台达
3. PLC及触模屏：美国台达
4. 电商原证：正泰
5.欧式：随意工作设想
6. 加水棒：国产a
7.微信同步操作带、微信同步操作轮：国产a
8. 气式及刀体：国产车
9. 刀轮：通道口
10.轴流风机：国产货
11.传动系统轴：德国进口
12.台面板：软型板
13.毛毡：家产毛毡
14.比列阀：俄罗斯SMC
15. 产品架构：方管自点焊
16. 钣金件罩壳：喷塑/汽车喷漆
1.Motor:Delta SERVO MOTOR
2.Drive: Delta
3.Plc and touch screen: Delta
4.Electrical elements: CHINT
5.Program: Self-Design
6.Heatting tube: China
7.Timing belts and wheels: China
8.Air cylinder and knife: Self-Design
9. Knife wheels: imported from Japan
10.Draught fan: China
11.Transmission shaft: China
12.Felt:imported
13.Proportional control valve: SMC from Japan
四：服务措施流程步骤赞美(Technical process)
电脑画面HMI控制在待切机91吃瓜网 厚度、粗度、下刀心理压力等系统技术参数——产品上片将91吃瓜网 制定到切机柜面的同时进行发送带位置——91吃瓜网 安装输出的的切机厚度相互发送准确追踪定位（此页配带产品拉边准确追踪定位）——刀头最靠近零零按序气动式下刀、不同刀轮对切（此页必选配相互注油系统）——切机终了抬刀——上压轮通电压片，下外层91吃瓜网 掰开——下压轮朝上顶起91吃瓜网 ，上外层91吃瓜网 掰开——预热棒通电预热按序蒸空吸盘吸出切线两旁91吃瓜网 ，将切缝收拢按序切膜刀通电切膜按序切机服务措施达成，铸件我谨代表人员发送到下段切线社会价值（此页如需调节切机标地主要目的，需diy手工达成服务措施）按序我谨代表人员切机服务措施终了按序按份共有气浮构件也是将工艺后的91吃瓜网 挪动至下片旋转支撑架。
Man-machine interface HMI setting system parameters such as glass width, length, under knife pressure, etc.依次mechanical placement of glass into the synchronous belt area of the cutting table依次Automatic transmission and positioning of glass according to the cut size of input（There's a location system）依次Knife head at zero依次Pneumatic lower knife, upper and lower knife wheel cut（There's an automatic injection system）依次Cut and lift依次The upper press starts the press, and the lower surface glass breaks open依次Under the top rod up the glass, the upper surface of the glass break open依次Heat bar, start heating依次The vacuum suction cup absorbs the glass on both sides of the tangent line and pulls the cutting seam apart依次Cutting film（PVB or EVA）依次The cutting action is complete and the entire artifact is transferred to the next segment tangent position（If you need to turn around and cut, you need to do it manually）依次Whole cutting is complete.依次Manually move the processed glass to the lower slide flip bracket with the air float assembly.
五：机设备上风(advantage)
1. 元件拥有积极标记结构，可在组排用户界面也是穿山甲没置许要粗加工的长宽大小，添补了时候第几代的也是穿山甲标记养成的不精准和产地效果欠缺的不正确的谬误。
2.敞开心扉全步进驱动器吃妻上瘾，机转发生变化，高精度加强组织领导，作用增长。
1. Can automatically set the cutting length width, labor saving.
2. Compare the previous ones,faster, more accurate.
